Differences

This shows you the differences between two versions of the page.

--- playground:startup [2023/08/15 17:21]
carter
+++ playground:startup [2023/09/07 04:14]
carter
@@ Line 75: / Line 75: @@
 **5.	Dipole Magnet Setup Instructions**
- **FOR OPERATION IN THE LARGE AND SMALL TARGET AREAS
+ a. Confirm that the Heinzinger power supplies are powered on in the Small Target Room with the following LED's illuminated:  Red "ON", and Green "Remote".  If Off, Press the "Local/Remote" button to "Local"; then "Stby" then "On"; then "Local/Remote" to "Remote".
-**
-** Note!  These instructions are obsolete, see Don or Greg for new operating instructions
+ b. If not already visible on the control room computer screen, start the appropriate software GUI's using the "Restart" button for "analyzer, switcher, swinger, or tweaker" magnets.
-**
- a.  Make sure both "analyzer" and "switcher_hz422" GUI's are turned down to zero amps using the GUI slider.
- b.  Confirm that the breaker on the beamline near the analyzer magnet is in the down "switch" position.
+ c. In the "Switcher_hz422" and "Analyzer_hz422" GUI windows, magnet beam deflection (left/right) is indicated on the "Magnet Current" line indicated as beam "left or right".  The "Swinger_hz422" and "Tweaker" has no polarity reversal button.
- c.  Switch the console "300 Amp ANAL/SWINGER" power supply to the "ANAL" mode using the deflection pushbutton switch.  If in the "SWING" mode press the "deflection" push button switch and wait for it to switch to the "ANAL" (right) mode, then press the "ON" pushbutton switch.
- d. Confirm that the "SWINGER" Heinzinger power supply is on with the following LED's illuminated:  Red "ON", and Green "Remote".  If Off, Press the "Local/Remote" button to "Local"; then "Stby" then "On"; then "Local/Remote" to "Remote".
- e. In "Switcher_hz422" GUI window, magnet deflection (left/right) is indicated on the "Switcher Magnet Current" line indicated as beam "left or right".
- f. The polarity can be toggled using the "Polarity" button located to the right of the "Lock" button.  When the "Polarity" button is pressed, the magnet current will automatically be set to zero and the polarity will reverse.
- g. Run the slider to the desired current.
-**  FOR OPERATION ON THE SWINGER MAGNET
-**
-** Note!  These instructions are obsolete, see Don or Greg for new operating instructions
-**
- a.  Make sure both "analyzer" and "switcher_hz422" GUI's are turned down to zero amps using the GUI slider.
- b.  Confirm that the breaker on the beamline near the analyzer magnet is in the up "null" position.
- c. Switch the "300 Amp ANAL/SWINGER" power supply to the "SWING" mode using the deflection pushbutton switch.  If in the "ANAL" mode press the "deflection" push button switch and wait for it to switch to the "SWING" (left) mode, then press the "ON" pushbutton switch.
- d. Confirm that the "SWINGER" Heinzinger power supply is on with the following LED's illuminated:  Red "ON", and Green "Remote".  If Off, Press the "Local/Remote" button to "Local"; then "Stby" then "On"; then "Local/Remote" to "Remote".
- e. Do not go over 20 Amps of Switcher/Anal current in the null mode.  If you do, the breaker near the analyzer magnet may trip and need to be reset to the "Null" position after running the magnet to zero current.
- f. The polarity can be toggled using the "Polarity" button located to the right of the "Lock" button.  When the "Polarity" button is pressed, the magnet current will automaticaly be set to zero and the polarity will reverse.
- g. Run the slider to the desired current.
+ d. The polarity can be toggled using the "Polarity" button located to the right of the "Lock" button.  When the "Polarity" button is pressed, the magnet current will automatically be set to zero and the polarity will reverse.
+ e. Run the slider to the desired current.

Accelerator Handbook

User Tools

Site Tools

Differences

Page Tools