Differences

This shows you the differences between two versions of the page.

--- playground:alphatross [2020/03/17 12:19]
jacobs created
+++ playground:alphatross [2020/03/17 15:52]
jacobs
@@ Line 1: / Line 1: @@
 ==== NEC Alphatross RF Source Instructions ====
-** Duoplasmatron Instructions **
+THESE ARE DRAFT INSTRUCTIONS WRITTEN REMOTELY.  THERE MAY BE OMISSIONS AND INCORRECT NOMENCLATURE, USE YOUR OWN JUDGEMENT...
-**Please study the diagram below.**
+**  __START UP__ **
-{{playground:duo.jpg|}}
+** In the Vault **
+  - LE Extension vacuum must be good as evidenced by Ion Gauge controller with orange displays on magnet.
+  - Source vacuum must be good as evidenced by Ion Gauge controller with blue displays in 19" rack.
+  - Unground alpha source and hang shepherd's hook on concrete wall conduits, close gate.
+  - Go around and unground sputter source, hang shepherd's hook on gate, and close gate.
+** In the Control Room **
-These instructions were developed by David Ingram, please e-mail any comments or questions about them to him, at ingram@ohio.edu.
+  - Source camera must have a view of the faraday screen on the blue box of the source head.
+    - To gain control of the source camera: On the joystick unit press "2" then "CAM" to specify the camera.
-This page includes: Duoplasmatron cold start, warm start, start from standby; shutdown completely, shutdown for warm start, shutdown to standby; Trouble shooting; 3He operation.
+    - Use the joystick and "TELE" or "WIDE" to create a view of interest.
+  - If not already present, launch the Alphatross software on the source computer.
+  - In prompt succession press the "on" buttons for: Water Cooling, Source Power, and He4 Gas.
-** Duoplasmatron Start-up **
+    - These actions start a 60 second timer on the RF supply and set initial conditions on the Magnet and Mass Flow Controller.
+    - After 60 seconds the RF power starts, gives a reading on the meter above the faraday screen, and hopefully the plasma will ignite giving an intense white glow.  It is bright enough to illuminate the faraday screen if not looking directly at it in the mirror.
-You need to determine what the state of the source is before you do anything. Depending on the electrical and vacuum status the source will be starting from cold, warm, or standby.
+  - Plasma or not, raise the Magnet to 4 A, maybe the plasma will ignite.
+    - Monitor the Ion Gauge pressure, it should remain less than 4 x 10-6 Torr while setting the Probe.  It should settle to around 2 x 10-6 or less when done.
-The first check you need to make is on the vacuum status of the source. The source pressure should be less than 5x10<sup>-6</sup> torr. If it is not find out why before going any further.
+    - Raise the Probe Voltage to 3 KV as a start, this might be enough to get the plasma going.
+    - If there is still no plasma try raising the Mass Flow setting to as much as .5 SCCM to inspire ignition and then return to .35 SCCM.
-If the control power for the machine, and/or for the source are off, or if the sodium canal supply is off or at zero current, you are starting from the cold state.
+    - Monitor the Probe Current, maintain 3 mA +/- 1 mA, and continue raising the Probe Voltage until it reaches 6.5 KV.
+  - Set the Oven Voltage to 87 V, wait ten minutes.  After 10 minutes the Oven Temp should be around 150 C.
-If the power to the source console is on and the sodium canal heater current is ~0.3 A and a beam has been successfully extracted previously, then the source is starting already warm.
+  - Set the Extractor Voltage to 5.5 KV and the Bias Voltage to a value that gives the desired injection energy less (6.5 + 5.5). Beam yield seems to increase with injection energy above 30 KeV.  Suggest trying 41 or 53 KeV settings if pulsing.
+    -
-If the power to the source console is on and the sodium canal heater current is ~0.55 A and there is ~0.75 A of arc and the extraction and canal supplies are on, then the source is in standby.
-If the source is in any other state please ask before proceeding.
-** Starting warm **
-This applies when the source already been run successfully and the Sodium heater current left at ~0.3 A, and is the usual state from which to start the source.
-At the Control Console:
-. Check the source vacuum is less than 5x10<sup>-6</sup> torr.
-In the Vault:

Accelerator Handbook

User Tools

Site Tools

Differences

Page Tools